Gpenny 2.2KW ER20 D80 110v Air cooled spindle motor(Ceramic ball bearings) kit, QL Inverter, 80mm Bracket

£409.80

Category:

Description

Price: $409.80
(as of Jun 07, 2025 05:47:48 UTC – Details)

Product Description

2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket

Basic parameter

Size: 80*224mm

Cooling: Air cooling

Power: 2.2KW

Voltage: 110v

Current: 20A

Frequency: 400Hz

Speed: 0-24000rpm

Runout Off: Less than 0.01mm

Diameter: 80mm

4 PCS Fully sealed angular contact bearings

Collet: ER20

Grease Lubrication

2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket

We are the spindle manufacturer,we use better material to produce the spindle.

1.We use steel bearings seat,spindle will not morph during the using life.Increase the spindle using life.

2.We use 4 pcs 7 series fully sealed angular contact ball bearings, it quality much better, usually use it 1-2 years without any problems.

3. Full power spindle, stronger shaft and coil,more power in engraving and cutting working.

4. Precision 0.01mm.Coaxial degree less than 0.0025mm,suitable for high accuracy work.

5. Carefull assembly make the spindle more precisional. 3-4 hours testing after assemble, 99.9% pass rate. No worry after ordering.

6. We work with biggest CNC router manufacturer in USA, EU,RU. Strong work partners.

Main ApplicationMain Application

2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket

Basic parameter

Power: 2.2KW

Input Voltage: 110v

Input Phase: 1 or 3 phase

Input Frequency: 50-60Hz

Output Voltage: 110v

Output Current: 17.5A

Output Frequency: 0-1000Hz

Control Method: V/F control

2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket

Basic parameter

Diameter: 80mm

Material: Cast Aluminium

Feature:

Compared with the aluminium profile fixture,the accuracy is much higher , and it is hard to deform.

Inner wall is very smooth, outer walls is sandblasted, relatively fine uniform, but not very smooth.

Cast aluminium fixture is much heavier than aluminiumprofile fixture.

2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket

If the spindle will not be used for a long time, please keep the spindle oil sealed to prevent rust from being unused for a long time. Before shipping , we did the oil seal to avoid the rust during the long shipment. When you get the spindle, please clearing the oil seal before using. Thank you.

Water cooled spindle MUST be used with water pump. Otherwise the spindle will soon broken.

AC spindle motor MUST use with inverter. The power of inverter need equal or bigger than the spindle power. Before using,please set up the inverter parameters suitable for spindle. Otherwise the spindle and inverter will broken at once.

When you use the spindle,the noise is not same as always,please STOP the spindle at once. You may need to replace the spindle bearings.

2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket2.2KW ER20 D80 110V/220V Air cooled spindle motor with H100 Inverter with Bracket

AC 110V Spindle motor (Must need connect to inverter/VFD)
4PCS 7Series angular contact bearing, exterd the spindle using life.
Spindle connect to GND, Pin-4 connect to inverter GND.
Spindle 1-2-3 connect to Inverter U. V. W.
Spindle motor used 4pcs ceramic ball bearings.

Reviews

There are no reviews yet.